• Simple and rapid installation
• Highly sensitive receiver and built-in external antenna afford up to 200 ft. of range when used with commonly available X10 RF devices
• Recognizes all 256 house/unit X10 addresses and re-sends those from RF wireless units over the powerline
• Any of the X10 addresses can be filtered out with a PC based utility
• Sets up easily to control INSTEON devices based on up to 20 received RF or powerline X10 addresses
• Timers can be set up on each address to send an OFF command automatically from .5 to 15.5 minutes after the ON command is received
• Totally configurable over the INSTEON network through PC or web based applications
• Supported by an ever-growing list of home automation applications from third parties.

Improves the usability of wireless X10 while blending the X10 and INSTEON Worlds
Now you can integrate any RF wireless X10 devices them into a reliable INSTEON network. The EZX10RF receives RF signals from up to 200 feet away and rebroadcasts them on your power lines. It decodes all 256 X10 house/unit signals, any of which can be filtered out if you desire. X10 RF or powerline codes can be set up to control single or multiple (group) INSTEON devices.

Use X10 and INSTEON Interchangeably around Your Home
Now you can use an X10 handheld remote to trigger the EZX10RF to turn on your porch light via INSTEON as you approach the front door. Or you can use an outdoor X10 motion sensor in the garden to trigger an INSTEON scene that turns on your landscape lighting and water features. There are other possibilities such as using a palmpad X10 controller to turn off or on the sprinklers while making periodic adjustments in the yard. Or, turning on a set of lights from your car through your X10 compatible HomelinkTM opener..


INSTEON and X10 compatibility means virtually unlimited connectivity, including wireless networks and the Internet.

EZX10RF is easy to install and operate, and may be used in conjunction with home automation programs such as HouseLinc from Smarthome, mControl from Embedded Automation or Indigo from Perceptive Automation. Please check the specific software you plan to use for the most current information regarding support for your EZX10RF. Our free, Windows XP utility can also be used with our EZSrve/EZBridge or a Smarthome PLC to enhance the manual initial set up as follows:

• Verification of INSTEON EZX10RF communications
• Filtering of unwanted X10 addresses
• Modification of the response to a given X10 address (commands sent, broadcast vs. group command, timer enabling, etc)
• Set up of delay timers
• Modifications to the INSTEON links database

General
SimpleHomeNet Product Number	EZX10RF All-House X10 Transceiver and Insteon Bridge #5010G
Warranty	1 year
Operation
Status LED (on the PLM)	White or Blue
Setup Memory	Non-volatile EEPROM
INSTEON Features
INSTEON Addresses	1 hard-coded out of 16,777,216 possible
INSTEON Links	30
INSTEON Powerline Frequency	131.65 KHz
INSTEON Minimum Transmit Level	3.2 Vppinto 5 Ohms
INSTEON Minimum Receive Level	10 mVppnominal
INSTEON Messages Repeated	Yes
X10 Features
X10 Primary Address	None needed for operation
X10 Powerline Frequency	121 KHz
X10 Minimum Transmit Level	3.2 Vppinto 5 Ohms
X10 Minimum Receive Level	20 mVppnominal
X10 Messages Repeated	No
Mechanical
Operating Conditions	Indoors, 32 to 122°F, up to 85% relative humidity
Dimensions	4.0" H x 2.5" W x 1.5" D
Weight	5 oz
Electrical
Supply Voltage	120 Volts AC +/- 10%, 60 Hertz, single phase
Surge Protection	MOV rated for 150 Volts
Power Plug	3-pin grounded
Pass-through Outlet	3-pin grounded
Certification	Safety tested for use in USA and Canada (ETL #3101636)

EZX10RF X10 All-Hose Transceiver and INSTEON Bridge
EZX10 Quick Set-up Guide		Instructions on EZX10RF set up and use
SimpleHomeNet Utility Suite		A utility suite to setup and use SimpleHomeNet devices with EZSrve/Bridge or a Smarthome PLC
EZX10RF Command Set		Complete details for those writing custom applications to support EZX10RF